All Articles
Commercial Saunas for Gyms, Hotels and Resorts in Thailand
The sauna in a private garden is used four or five times a week by the same two…
Free Delivery · 1–2 Yr Warranty · After-sales Support
A solid pine soaking tub built the way barrels have been made for centuries. Individual staves cut to a taper, fitted edge to edge, and drawn together by steel hoops. There is no liner and no sealant holding the water in. The timber swells when it gets wet and the joints close on themselves.
price updates live
This bath holds about 760 litres. Outdoors, the 1.5HP chiller is the smallest that suits it. Contact us
Have more questions? Chat with us
The pine is sustainably sourced and finished with an eco-friendly oil stain that is
skin-safe and free from harsh chemicals. Nothing synthetic touches the water. Just
timber, steel and whatever you fill it with.
At 1250 × 650 × 600 mm it holds around 220 litres and seats one person in a proper
deep soak, shoulders under. Fill it hot for a traditional timber bath or cold for a
plunge; pine is stable across the full range and does not mind being switched.
A centre-bottom floor drain takes a standard 40 mm waste fitting, so emptying is a
matter of pulling the plug rather than bailing. A slatted wooden step is included.
Light enough that two people can carry it into position and move it later if the
garden changes. No installation, no plumbing trade, no electrical connection.
Bare timber asks for a slightly different routine to a plastic tub. Rinse it after
use, drain it fully rather than most of the way, and let it dry between sessions.
Re-oil it once or twice a year. If you are running it commercially, drain it every
night and treat the inside as a surface to be cleaned rather than water to be
dosed. The full routine, including what to use and what not to, is under Care &
Maintenance below.
Delivered to your door across Thailand. For island delivery a ferry surcharge
applies and is confirmed at checkout.
Inspect the tub on arrival before signing off the delivery. Any transit damage must
be noted on the delivery docket at the time of receipt.
No installation is required and no trade is needed on site.
The tub arrives assembled. There is nothing to build.
Placing it
Stand it on a level, water-tolerant surface. Concrete, tile, a paved terrace or a
properly framed deck all work. Level matters: a tub sitting out of level fills
unevenly and the waterline shows it.
Connect the floor drain to a 40 mm waste outlet, or simply position the tub over an
area that drains. The waste trap and pipework are not included and are available
from any plumbing supplier. Fill with a hose or by bucket.
First use
Fill and empty the tub once before your first proper soak. This lets the staves
take up water and tighten, and lets any initial movement in the timber settle.
A small amount of seepage at the joins on that first fill is normal. It is how
stave-coopered timber works, and it stops within one or two fills as the pine
swells. It is not a fault and it does not need sealing.
For the same reason, a tub left empty and dry for weeks will weep briefly when you
next fill it, then close up again.
Weight when full
Around 220 litres of water, so roughly 220 kg, plus the tub and the person in it.
On a ground-floor slab this is rarely an issue. On a balcony, a roof or a timber
deck, have the structure checked before delivery.
No electrical or plumbing trade work is required.
If an electrical item stops working within the warranty period, we’ll send you a replacement free of charge.
One-year warranty on the timber structure.
The warranty does not cover normal wear and tear, misuse, or modification. It also
does not cover seepage at the joins during the first fills, which is how a
stave-coopered tub is supposed to behave and is described under Assembly & Setup.
Chlorine damage is not covered. Chlorine breaks down the fibre of the wood and
should not be used in this tub.
After each use
- Rinse the interior with clean water.
- For a deeper clean, use a mild natural soap and a soft brush. Avoid harsh
chemical cleaners, which strip the oil finish and dry the timber out.
- Drain it fully rather than most of the way, and let it dry.
Oil finish maintenance
- Re-apply a food-safe or eco timber oil once or twice a year, or whenever the wood
starts to look dry.
- Do not apply varnish or polyurethane over the existing finish. They are
incompatible with an oil-stain base and will not bond.
Cold use
- Change the water regularly. A chiller with filtration will hold the temperature
and keep the water clear, but filtration removes particles rather than bacteria,
so it extends the interval between changes rather than replacing them.
- Cold water still grows things. It just does it more slowly.
Commercial and shared use
Run it as a single-bather plunge. One person at a time, then drain. The water is
not sanitised between users.
The timber is bare on the inside with an oil finish rather than a sealed surface,
so it cannot hold a chlorine residual the way a stainless bath can. Chlorine breaks
down the fibre of the wood itself and should not be used.
Nightly, for daily commercial use
- Drain fully. Not most of the way — standing water in the base is where things
grow.
- Rinse with clean water and clear out any debris.
- Wipe the interior with a soft cloth or brush and a mild natural soap, then rinse
again.
- Spray the interior with 3% hydrogen peroxide. Coat it, leave it ten minutes, and
do not rinse. It breaks down into water and oxygen and leaves nothing behind.
- Let it dry properly before the next fill.
Test the peroxide on a hidden patch low down at the back before you make it a
routine. Peroxide lightens timber, and on the darker stains you want to know what
it does before it does it across the whole tub.
Drying it out
Drying matters as much as anything else on this list. Mould and bacteria need
moisture, and a tub that dries between sessions does most of the work on its own.
Two people can tip it up. Stand it on its side against a wall, or turn it over and
prop one edge on a batten or a block so it sits at an angle. Do not lay it
face-down flat on the ground — that seals the opening and traps the damp
underneath, which is the opposite of what you are after. It needs a gap for air to
move through.
Leave the cover off while it dries.
Weekly
Give it a firmer wipe-down and check the joins and the base, where anything that is
going to establish will establish first. If the timber is looking dry, that is the
oil due.
Stock items can be returned within 7 days of delivery in resalable condition. Custom and made to order items cannot be returned once production has begun. Faulty goods are repaired, replaced or refunded at our cost.
Built to order
Every bath is made after the order is placed. Because nothing is built until you
order it, made-to-order baths cannot be returned or exchanged for change of mind.
Anything faulty is covered under warranty.
Deposit and balance
A deposit confirms the order and starts production. The balance falls due before
dispatch. Your quote states both figures.
Prices
Quoted prices hold for 30 days. They include 7% VAT and delivery within Thailand.
They exclude electrical work, structural certification, crane hire and any site
preparation.
Site readiness
The base, the access route and the power supply are the customer's responsibility
and need to be ready on the delivery date. Where a bath is going onto a roof, a
balcony, a deck or any suspended floor, written structural sign-off is required
before delivery.
Changes
Specification changes are possible before production starts. Once the build is
under way a change may not be possible, and where it is, it may carry a cost.
Colour and grain
Timber is a natural material. Colour, grain and figure vary between boards and
between baths, and timber left outdoors changes colour over time. Photographs are
representative rather than exact.
Tell us where to send it. We'll email your quote with all the products and options you've selected.
Taking you to the confirmation page…